Product Overview
Buying a watch strap online for a Cartier comes down to two things: the gap between the lugs, and whether the ends of the band follow the shape of the case. This one is built around both. It is a replacement strap in FKM fluororubber — the dense, matte rubber normally found on dive watches — cut in the narrow widths Cartier cases use and finished with ends that meet the case instead of standing away from it. Most Cartier dress models leave the workshop on leather. Leather is right for a boardroom and wrong for almost everything else: it darkens with sweat, softens in the rain and eventually splits at the buckle. Moving to rubber gives the same watch a second, more casual life — a long flight, a gym session, a wet weekend — without touching the case, the dial or the proportions. Only the part that touches your wrist changes. The band is 2.5 mm thick and weighs 14 g, so a slim rectangular case does not suddenly feel like a sports watch, and the matte surface stays quiet next to polished steel or gold. Nothing here needs a specialist. The band arrives with stainless steel spring bars, the ends press into the lugs by hand, and the tang buckle is already fitted when it reaches you.
Fluororubber Construction
The material is why this band can live on a dress watch. FKM — fluoroelastomer, normally written fluorine rubber — is the compound used for engine seals and dive-watch straps, and it behaves quite differently from ordinary silicone. It stands up to heat, UV, sweat and the oils in your skin, and it does not yellow, crack or turn sticky as it ages. Water, fresh or salt, leaves it unchanged.
That matters more on a Cartier than on a beater. A band on a dress watch is expected to look presentable for years, through sunlight from an office window, a hot commute and repeated handwashing. A fluororubber material watch strap takes that without fading or going dull, which is usually the point at which lower-grade rubber gives itself away.
The surface is smooth and matte with a soft, slightly dry touch — nothing tacky, nothing that grabs at a shirt cuff. It flexes from the first wear rather than needing a break-in period, and the underside carries cleanly moulded markings and edges that have been finished rather than left raw.
Weight and thickness complete the picture. At 2.5 mm and 14 g, the band adds almost nothing to a slim case; a Tank that disappears under a shirt cuff on leather still disappears on rubber.
Curved-End Fit
The ends of this band are not cut straight. Each one is moulded with a curve that follows the underside of the case, so the rubber meets the watch along a line rather than stopping short of it. On a rectangular Tank that is the difference between a band that looks fitted and one that looks borrowed — straight ends leave a step at each lug that catches the light and shows a sliver of spring bar.
The curve also changes how the band behaves in wear. Because the end sits against the case instead of pulling away from it, the strap leaves the lugs at a gentler angle and the first part of the arc falls over the top of the wrist rather than standing up. On a watch as flat as a Tank or a Ronde Solo, that keeps the whole assembly low.
Thickness at the lug end is held to 2.5 mm for the same reason: the band should blend into the case profile, not sit on top of it. A custom fluororubber material watch strap with a correctly matched curve looks like it was specified with the watch, which is the whole point of paying attention to this detail.
One thing to check: this band is made for cases that take standard spring bars and a conventional lug. If your watch has an integrated bracelet or a proprietary fitting, tell us the reference before ordering so we can point you to the right option.
Lug Width & Sizing
- Order the number you measured — the band is made in 14 mm, 15 mm, 16 mm, 17 mm and 18 mm, and each is a separate option. Widths are not forgiving: 16 mm will not squeeze into a 15 mm gap, and a 15 mm band will shift inside a 16 mm one.
- The two lengths — 110 mm on the long side and 70 mm on the buckle side, which puts the buckle underneath the wrist rather than at the edge of it.
- Setting the fit — the tail is punched so the tang buckle can be set at several points. Move it one hole at a time and check that the case still sits centred on top of the wrist.
- Do not order from the case size — a 34 mm case and a 40 mm case can take the same lug width, and two versions of the same model can take different ones. The gap between the lugs is the only number that decides it.
- Why there is no size chart by model — Cartier has used more than one lug width across versions of the same watch, so a chart based on the model name would be a guess. The measurement is the only reliable figure.
- Outside the range — if your case measures below 14 mm or above 18 mm, stop and ask. For a case that is not on our list, a custom fluororubber material watch strap can be cut to the same measurement once we have the reference.
- Wrist size — the band is not sold in wrist sizes; the length is fixed at 110 + 70 mm and the buckle holes do the adjusting.
- Tank Must and Tank Solo — slim rectangular cases with short lugs, and the shape this 14–18 mm range was cut for. If the original leather has cracked at the buckle, this is a straight replacement.
- Tank Louis Cartier — the same narrow footprint, and at 2.5 mm the band keeps the low profile that lets the case sit flat under a cuff.
- Must de Cartier — made in several sizes over the years, so check the width on your own watch rather than ordering from the model name alone.
- Calibre de Cartier — a rounder, heavier case that carries rubber convincingly; the matte finish reads as a deliberate choice rather than a shortcut.
- Ronde Solo de Cartier (often sold as London) — a round dress case where a solid colour band adds contrast and makes the watch easy to wear with a T-shirt.
- Clé de Cartier — the key-shaped crown stays the focus, and a plain, untextured band gives it a clean background.
- Anything not listed — send the reference and a photo of the case between the lugs, and we will say whether a custom fluororubber material watch strap in your width is the answer or whether a different option fits better.
Colourways & Buckle Finishes
- Black — the default for a reason. It works with steel, yellow gold and rose gold, and it is the shade that looks least like an addition.
- Deep brown and brown — the warmest options and the closest in spirit to the leather you are replacing; easy with tan shoes and a brown belt.
- Mustard yellow — a vintage note that suits steel cases and a casual wardrobe, and one of the shades that works especially well on a watch worn a little loose.
- Blue — quiet and slightly formal; it sits well with navy tailoring and reads darker in person than it does on a screen.
- Red — the loudest of the eight, and the colour shown on the wrist in the photographs. Especially good on a steel case, and particularly suited to summer.
- Orange and light purple — the two that change a watch's character most. Pick them if the point is that people notice.
- Silver, gold or rose-gold tone buckle — every colour is offered with all three, so match the case metal; on a two-tone watch the silver tone usually disappears most cleanly.
- Screen versus bench — colours can differ slightly from what a monitor shows, so judge the shade against your own watch and your own clothes rather than against the photo alone.
- Beyond the eight — the shades on this product are the stock range. For something else we take on custom fluororubber material watch straps, so ask before you settle for a colour that is nearly right.
Care & Storage
Rubber asks for very little, but a minute now and then keeps it looking new. After a hot day or a session at the gym, rinse this fluororubber material watch strap under lukewarm fresh water, work a drop of mild hand soap over the surface if sunscreen or lotion has built up, and pat it dry with a soft cloth. Sweat left to dry leaves a pale bloom that is far easier to rinse off than to polish out.
Keep solvent-based cleaners, neat perfume and long stretches of direct sun away from it. FKM handles heat and UV far better than silicone, but nothing enjoys a summer on a car dashboard.
Store the watch flat or on a cushion rather than folded under other pieces in a drawer, where a buckle can press a crease into the rubber over months. If a spring bar ever starts to look pitted or feels stiff, replace it rather than waiting for it to let go — bars cost very little and the alternative is a watch on the floor.
The buckle needs nothing more than the same soft cloth. A quick wipe after a hot day keeps the finish even and stops dried sweat collecting in the corners of the frame.
Fitting the Band
- Lay the watch face-down on a soft cloth with the case supported, so nothing presses on the crystal.
- Slide the fork of a spring bar tool into the notch between the band and the lug, and press the flange of the spring bar inward.
- With the bar compressed, tilt the old band away from the case and lift it out of the lugs.
- Take the new band, seat one tip of the spring bar in the lug hole, compress the other tip and ease it down into the second hole.
- Release the bar and pull the band gently away from the case. If it holds, the bar is seated; if it slips, reset it before moving on.
- Repeat on the other side and set the buckle. The same steps cover a stock band or a custom fluororubber material watch strap made to your width.
Specifications
| Specification | Detail |
|---|
| Material | FKM fluororubber (fluorine rubber) |
| Lug widths | 14 mm, 15 mm, 16 mm, 17 mm, 18 mm |
| Strap length | 110 mm + 70 mm |
| Thickness | 2.5 mm |
| Weight | 14 g |
| Ends | Curved, moulded to follow the case |
| Buckle | Stainless steel tang buckle |
| Buckle finishes | Silver, gold, rose-gold tone |
| Colours | Black, brown, deep brown, mustard yellow, blue, red, orange, light purple |
| Surface | Smooth matte |
| Water | Band material is unaffected by water |
Also in the Range
If the Cartier shares a drawer with other watches, the rest of the collection covers the neighbours. The tropical-style silicone quick release band, in 18 mm, 20 mm and 22 mm, is the softer and sportier option and swaps without tools — useful for a watch that sees the gym more often than the office. The fluororubber strap in 20 mm and 22 mm is the one to look at when the case is larger and rounder than a Tank. For a woven look with the same rubber practicality, the FKM fluororubber nylon band comes in 20 mm, 22 mm and 24 mm. And if you want the leather look back on a dress watch, the crocodile leather strap made for Longines and similar cases is the closest in character to what the Cartier originally came with.
Ordering & Custom Options
- Note the lug width in millimetres and the watch reference before you start, so the two can be checked against each other.
- Choose the colour and the buckle finish — silver, gold or rose-gold tone — to suit the case.
- Add your watch model in the order notes when you order this watch strap online; it is the quickest way for us to catch a width that will not fit before the parcel leaves.
- Ask about custom fluororubber material watch straps if you need a shade outside the eight, or your own mark on the band. We will confirm what is possible, the quantity involved and the timing.
- Confirm delivery, shipping cost and any import duties with our team before paying. Both depend on where you are and how much you order, so they are quoted per order rather than fixed on this product.
Warranty & After-Sales
Every order is checked before it leaves us, and our support does not stop at delivery. Email our after-sales team and a named contact replies with clear next steps. If an item arrives damaged, faulty or different from what you ordered, we arrange a replacement or the right parts. Need help fitting or using your purchase? We will walk you through it remotely, step by step, and keep replacement parts available afterwards. FUERMAN has served customers worldwide since 2010 with a team of 60+, and we stay reachable long after the order.
FAQ
How do I measure the lug width on my Cartier?
Take the old band off, then read across the inside faces of the two lugs with a steel rule or a soft tape, in millimetres — not across the outside of the case, and not the width of the strap you have just removed. A worn leather band can measure a fraction wider than the gap it came out of, so the watch is the reference, not the old strap. This is the step that goes wrong most often when buying a watch strap online: if the reading lands cleanly on 14, 15, 16, 17 or 18 mm, order that width, and if it sits between two of them, send us a photo of the gap with the rule in place before you buy.
Can I keep my Cartier folding clasp?
Yes. The band is made to accept the original Cartier deployant clasp, so the folding clasp you already own can move across and keep the signed hardware on the watch. If you would rather not swap it over, a stainless steel tang buckle comes fitted with the band in silver, gold or rose-gold tone. Decide which one you want before you fit it, because changing your mind later means taking the band off the watch again.
Do I need a watchmaker to fit it?
No. The band arrives with stainless steel spring bars and presses into the lugs by hand in a few minutes. A spring bar tool makes it easier and keeps the case away from a knife blade, which is what most people reach for when there is nothing else in the drawer. Work over a soft cloth and check both ends are properly seated before you wear the watch. If your case has drilled lugs or very tight clearance, a watchmaker can do it in minutes.
Will a rubber band look out of place on a Tank?
Not if you choose the colour for the occasion. Black, deep brown and blue keep the watch formal and pass unnoticed under a cuff; red, orange and mustard yellow are meant to be seen and work well with short sleeves. Because the band is only 2.5 mm thick, it does not change the silhouette of the case — the watch still reads as a Tank, just a less formal one. Think of it as a second strap rather than a replacement for leather.
Can I swim and shower in it?
The band itself is fine in water. Swimming, showering, salt water and chlorinated pools will not damage FKM or change its colour, and a rinse in fresh water followed by a wipe with a soft cloth is all it needs afterwards. What the band cannot do is change the watch: water resistance is set by the case, its gaskets and its crown, so swim with the watch only if the case itself is rated for it.
Can I order custom fluororubber material watch straps in another colour, or with my own marking?
Yes. The eight shades on this product are the stock range, and beyond them we work to a colour you send us — a sample, a swatch or a reference we can match. Tell us the shade, the width and the marking you have in mind, and we will come back with what can be done. Logo work on the band is handled the same way, so send the artwork with the enquiry rather than after the order.